Category
Paint Inspection Kit
Paint Inspection Kit

Paint Inspection Kit                                                                       Paint Test Equipment – UK

Conforms To International Standards
ISO 2808 ASTM D 4414-A
ISO 8502-3 ASTM B 499
ISO 8502-4 ASTM D 4417-C
ISO 8502-6 NACE RP0287
ISO 8502-9 ISO 8503-5

The Paint Inspection Kit is an essential piece of equipment for all industrial painters, enabling them to have all the necessary test equipment to ensure the industrial paint coating is correctly applied throughout the coating process in compliance with ISO Standards.

Supplied in an industrial foam-filled Carrying Case, ensuring that all the equipment is easily available and transportable.

The Equipment supplied in the Paint Inspection Kit will allow on site testing for all five stages of the following ISO Standards Coating.

 

STAGE 1 SURFACE PROFILE:

 

ISO 8503-5: Replica Tape method for the determination of the surface profile.

 

Testex Tape (R1002) and Testex Gauge (R1004)

A unique replica technique and a snap gauge makes possible accurate, blast-cleaned surface profile measurements.

Testex Tape makes surface replicas easy to obtain and produces average maximum peak-to-valley readings that ensure optimum blasting effectiveness. Replicas can be retained for future needs.

Packing: Testex Tape X Coarse (50 impression roll), Testex Gauge and Burnishing Tool.

STAGE 2 SURFACE CLEANLINESS :

ISO 8502-6: Extraction of soluble contaminants for analysis – the Bresle method.
ISO 8502-9: Field method for the conductometric determination of water-soluble salts.

Bresle Test (P2005)

Steel when blast-cleaned can be contaminated by Water-soluble salts and corrosion products. These compounds are almost colourless and are localized at the lowest point of the rust pits. If they are not removed prior to painting, chemical reactions can result in blister formation and accumulations of rust that destroy the adhesion between the substrate and the applied protective coating.

This contamination can be tested quickly and easily using the Bresle Test.

 

Packing: Bresle Conductivity Meter, Bresle Patches (pack of 50), 500ml Deionised Water, 5ml Syringe, Conductivity Meter Calibration Solution, Conductivity Meter Moistening Solution, Conductivity Meter Deionised Water and 25ml Beaker.

STAGE 3 SURFACE CLEANLINESS :

ISO 8502-3: Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method)

Dust Test (PS201)

Assess the quantity and size of dust particles on steel surfaces prepared for painting. Dust particles on blast-cleaned steel surfaces may reduce the adhesion of applied coatings, and by absorbing moisture may promote the corrosion of the steel surface.

Packing: Dust Test Tape (60m roll), Dust Test Charts (pack of 50) and X10 Illuminated Magnifier.

STAGE 4 CLIMATIC CONDITIONS :

ISO 8502-4: Guidance on the estimation of the probability of condensation prior to paint application

Dewpoint Meter (H3001)

The Dewpoint Meter enables testing for the estimation of the probability of condensation on a surface to be painted and establishing whether conditions at the job site are suitable for painting or not.

Packing: Dewpoint Meter, Humidity Sensor and Surface Temperature Probe.

STAGE 5 COATING THICKNESS :

ISO 2808: Paints and varnishes – Determination of film thickness

Eban 4000 Coating Thickness Meter (C4001)

Measures all coatings on steel and iron substrates using the magnetic induction principle, ensuring the correct coating thickness has been applied.

Other models of the Eban 4000 can be supplied for thick coatings or non-ferrous substrates.

Packing: Eban 4000 Coating Thickness Meter (C4001), flexible lead Probe, set of 8 Calibration Foils and Zero Disk.

 Paint Inspection Kit Specifications & Spares:
Part No Metric/Imperial
K3001 Paint Inspection Kit Metric
K3002 Paint Inspection Kit Imperial
F2001 Spare Calibration Foils 0-1000μm (25, 50, 75, 125, 175, 250, 500, 750μm)
Z1003 Spare Zero Disk Ferrous
R1002 Spare Testex Tape X Coarse (50 impressions) 40-115μm (1.5-4.5mils)
PS001 Spare Bresle Patches (pack of 50) Standard Adhesion
PS003 Spare Deionised Water (500ml)
PS004 Spare Syringes (pack of 3)
PS005 Spare Conductivity Meter Calibration Solutions (2 Solutions, 1 Deionised Water)
PS006 Spare Conductivity Meter Sensor
PS007 Spare 25ml Beaker
PS201 Spare Dust Test Tape 25mm (1”) 60m Roll
PS202 Spare Dust Test Comparator Charts (pack 50)
HS301 Spare Humidity Sensor 0–100%rh/-10 to 70°C (14 to 160°F)
HS302 Spare Surface Temperature Probe -20 to 80°C (-4 to 176°F)

 

Know Us
  
Download
Film Thickness List
Quick Enquiry
Name  :
Email   :
Company  :
Phone  :
Message  :
 
Contact Us
Samriddhi International Inc.
405, New Sonal Ind Est.,
Building No.2, Link Road,
Near BMW Showroom,
Kach Pada, Malad (W),
Mumbai 400 064
India
T : +91 22 4004 5104
E : info@samriddhiint.com,
     info@sbstesting.com